Qt:Документация 4.3.2/qxmlinputsource

Материал из Wiki.crossplatform.ru

Перейти к: навигация, поиск
40px Внимание: Актуальная версия перевода документации находится здесь

__NOTOC__

Image:qt-logo.png

Главная · Все классы · Основные классы · Классы по группам · Модули · Функции

Image:trolltech-logo.png

Содержание

[править] QXmlInputSource Class Reference
[модуль QtXml ]

The QXmlInputSource class provides the input data for the QXmlReader subclasses. More...

 #include <QXmlInputSource>

Note: All the functions in this class are reentrant.

[править] Открытые функции

[править] Защищенные функции

  • virtual QString fromRawData ( const QByteArray & data, bool beginning = false )

[править] Подробное описание

The QXmlInputSource class provides the input data for the QXmlReader subclasses.

All subclasses of QXmlReader read the input XML document from this class.

This class recognizes the encoding of the data by reading the encoding declaration in the XML file if it finds one, and reading the data using the corresponding encoding. If it does not find an encoding declaration, then it assumes that the data is either in UTF-8 or UTF-16, depending on whether it can find a byte-order mark.

There are two ways to populate the input source with data: you can construct it with a QIODevice* so that the input source reads the data from that device. Or you can set the data explicitly with one of the setData() functions.

Usually you either construct a QXmlInputSource that works on a QIODevice* or you construct an empty QXmlInputSource and set the data with setData(). There are only rare occasions where you would want to mix both methods.

The QXmlReader subclasses use the next() function to read the input character by character. If you want to start from the beginning again, use reset().

The functions data() and fetchData() are useful if you want to do something with the data other than parsing, e.g. displaying the raw XML file. The benefit of using the QXmlInputClass in such cases is that it tries to use the correct encoding.

See also QXmlReader and QXmlSimpleReader.


[править] Описание функций-членов

[править]
QXmlInputSource::QXmlInputSource ()

Constructs an input source which contains no data.

See also setData().

[править]
QXmlInputSource::QXmlInputSource ( QIODevice * dev )

Constructs an input source and gets the data from device dev. If dev is not open, it is opened in read-only mode. If dev is 0 or it is not possible to read from the device, the input source will contain no data.

See also setData(), fetchData(), and QIODevice.

[править]
QXmlInputSource::~QXmlInputSource () [virtual]

Destructor.

[править]
QString QXmlInputSource::data () const [virtual]

Returns the data the input source contains or an empty string if the input source does not contain any data.

See also setData(), QXmlInputSource(), and fetchData().

[править]
void QXmlInputSource::fetchData () [virtual]

This function reads more data from the device that was set during construction. If the input source already contained data, this function deletes that data first.

This object contains no data after a call to this function if the object was constructed without a device to read data from or if this function was not able to get more data from the device.

There are two occasions where a fetch is done implicitly by another function call: during construction (so that the object starts out with some initial data where available), and during a call to next() (if the data had run out).

You don't normally need to use this function if you use next().

See also data(), next(), and QXmlInputSource().

[править]
QString QXmlInputSource::fromRawData ( const QByteArray & data, bool beginning = false ) [virtual protected]

This function reads the XML file from data and tries to recognize the encoding. It converts the raw data data into a QString and returns it. It tries its best to get the correct encoding for the XML file.

If beginning is true, this function assumes that the data starts at the beginning of a new XML document and looks for an encoding declaration. If beginning is false, it converts the raw data using the encoding determined from prior calls.

[править] QChar QXmlInputSource::next () [virtual]

Returns the next character of the input source. If this function reaches the end of available data, it returns QXmlInputSource::EndOfData. If you call next() after that, it tries to fetch more data by calling fetchData(). If the fetchData() call results in new data, this function returns the first character of that data; otherwise it returns QXmlInputSource::EndOfDocument.

Readers, such as QXmlSimpleReader, will assume that the end of the XML document has been reached if the this function returns QXmlInputSource::EndOfDocument, and will check that the supplied input is well-formed. Therefore, when reimplementing this function, it is important to ensure that this behavior is duplicated.

See also reset(), fetchData(), QXmlSimpleReader::parse(), and QXmlSimpleReader::parseContinue().

[править]
void QXmlInputSource::reset () [virtual]

This function sets the position used by next() to the beginning of the data returned by data(). This is useful if you want to use the input source for more than one parse.

See also next().

[править]
void QXmlInputSource::setData ( const QString & dat ) [virtual]

Sets the data of the input source to dat.

If the input source already contains data, this function deletes that data first.

See also data().

[править]
void QXmlInputSource::setData ( const QByteArray & dat ) [virtual]

This is an overloaded member function, provided for convenience.

The data dat is passed through the correct text-codec, before it is set.


Copyright © 2007 Trolltech Trademarks
Qt 4.3.2